cometic stock numbers

gse_turbo · Post by **gse_turbo** » Sat Feb 24, 2007 4:38 am

i was going threw old emails and found this hope it helps some one. you can call cometic direct to order @ 1.800.752.9850.

garrett

C4216-051
VAUXHALL 16 VALVE 2L 88MM
.051" MLS HEAD GASKET
$86.50

C4216-060
VAUXHALL 16 VALVE 2L 88MM
.060" MLS HEAD GASKET
$100.90

C4216-065
VAUXHALL 16 VALVE 2L 88MM
.065" MLS HEAD GASKET
$100.90

C4216-074
VAUXHALL 16 VALVE 2L 88MM
.074" MLS HEAD GASKET
$109.15

Brandon Hare
Cometic Gasket
8090 Auburn Road
Concord, OH 44077
Phone: 440-354-0777 Ext. 133
Fax: 440-354-0350

Nubira2.2 · Post by **Nubira2.2** » Thu Mar 15, 2007 4:51 pm

im goint to buy one but not know which
i want to lower compression but not lower than 9.0:1
so that the car would made good power N/A form

any suggestions?

max boost i will run is 10psi

gse_turbo · Post by **gse_turbo** » Thu Mar 15, 2007 11:50 pm

.051 is OE size, .060 or .065 is you best bet. if your going turbo soon, go with the .065.

garrett

Nubira2.2 · Post by **Nubira2.2** » Fri Mar 16, 2007 4:57 am

car is already turbo
how mucho the compression will change with this gaskets ? .060 and .065?

gse_turbo · Post by **gse_turbo** » Sat Mar 17, 2007 9:54 pm

i'll get all the numbers you need to figure comp. ratio on monday and get back to you. just for reference, are you using a complete 2.2 motor or 2.2 crank in a 2.0 block?

garrett

Nubira2.2 · Post by **Nubira2.2** » Sat Mar 17, 2007 11:16 pm

im using a complete T22SED engine
how much CR with .060 and .065 gaskets?

wolfhound · Post by **wolfhound** » Mon Mar 19, 2007 8:57 am

Do they make for the 1600 Lanos 16v?

Séan

kroz123 · Post by **kroz123** » Mon Mar 19, 2007 4:52 pm

Well I have an Chevy Optra T18SED, Bore is 81.6MM
The only head gasket Cometic has is the one for the 1.6V 82MM C4257-051

So I bought that one.

What do you guys think, mi mech said to me that it could work.

Arvin

Deathwind · Post by **Deathwind** » Tue Mar 20, 2007 3:13 am

I'm not totaly sure about this.

But I think it wouldn't fit.

Maybe the gasket is for 1.6L engines not for 2.0L engine.

But it's just assume.

kroz123 · Post by **kroz123** » Tue Mar 20, 2007 3:15 am

well my engine is not a 2.0, it's a 1.8

gse_turbo · Post by **gse_turbo** » Tue Mar 20, 2007 4:00 am

quick question.

rr__kroz123 wrote:well my engine is not a 2.0, it's a 1.8

is your block cast with a six digit code like "R90 400 075". the reason for asking is that i think that your block is the same as the 2.0/2.2 but i've never seen the 1.8.
if your motor has the code starting with "R90" them the part #'s at the top of yjr page with work.

garrett

should be just to the left of the dipstick hole.

kroz123 · Post by **kroz123** » Tue Mar 20, 2007 4:03 am

gse_turbo wrote:quick question.

rr__kroz123 wrote:well my engine is not a 2.0, it's a 1.8
is your block cast with a six digit code like "R90 400 075". the reason for asking is that i think that your block is the same as the 2.0/2.2 but i've never seen the 1.8.
if your motor has the code starting with "R90" them the part #'s at the top of yjr page with work.

garrett

should be just to the left of the dipstick hole.

Well man I don't know I'll check tomorrow and post a pic of the nr.

gse_turbo · Post by **gse_turbo** » Tue Mar 20, 2007 4:10 am

i just pulled a pic off line and i can say for sure that they are the same motor.

garrett

gse_turbo · Post by **gse_turbo** » Thu Mar 22, 2007 1:19 am

nubira2.2, i'm trying to get you the exact numbers of the compression change but there is one figure i cant find or measure until i build my motor.
the figure i need is the "dech volume," the measurement i keep getting isn't consistent with what i should be getting.
if anyone knows this number please let me know.

garrett

kroz123 · Post by **kroz123** » Thu Mar 22, 2007 2:31 am

Hey gse_turbo.
Here it is,

So the cometic head gasket I have will work then?

The original daewootech forum

cometic stock numbers

cometic stock numbers

Hmm.

dech volume