Did Opel came with a 1.6 engine?

eljunito · Post by **eljunito** » Wed Mar 09, 2005 3:27 am

I'm looking for a 1.6 piston but high compression that can be adapted to my Lanos, which is 9.5 to 1. I want to increase the compression since the head block can't be reduce too much.

Junito

MMamdouh · Post by **MMamdouh** » Wed Mar 09, 2005 8:02 am

Yes Opel made a 1.6 engine with 8 valves and with 16 valves... i got no idea about the compression rations on those engines.

MMamdouh

norman · Post by **norman** » Wed Mar 09, 2005 10:17 am

moin,

look here http://www.die-opel-tuner.de/seiten/motoren/1600ccm.htm. only the engins with the cylindersize 79x81,5 (hub/bohrung). i think you have to make pockets into the pistons of the 8V for the valve?s. the highest compression ist 10,5:1. than you have to driver a better fuel (95 octan ROZ)
maybe take the pistons of the diesel engine (23,0:1)

tschau norman

NubiraPower · Post by **NubiraPower** » Wed Mar 09, 2005 12:15 pm

look here http://www.die-opel-tuner.de/seiten/motoren/1600ccm.htm. only the engins with the cylindersize 79x81,5 (hub/bohrung)

I don't understand what you want to say. My engine has the cylindersize 79x81,5. So I could find other pistons from opel to match my engine?

norman · Post by **norman** » Wed Mar 09, 2005 12:21 pm

moin,

My engine has the cylindersize 79x81,5. So I could find other pistons from opel to match my engine?

yes, but only in view of the cylindersize. i dont know, if the piston will fit to the daewoo piston rod. and if you use the piston rod and the piston from opel, it maybe will not fit to the crankshaft.
learning by doing

tschau norman

NubiraPower · Post by **NubiraPower** » Wed Mar 09, 2005 12:28 pm

yes, but only in view of the cylindersize. i dont know, if the piston will fit to the daewoo piston rod. and if you use the piston rod and the piston from opel, it maybe will not fit to the crankshaft.
learning by doing

I will try to buy pistons of opel engine C 16 XE and mount on my engine. 10x

eljunito · Post by **eljunito** » Thu Mar 10, 2005 2:18 am

Do you know a website where I can see the piston of Opel for 16v. My
plan is to change the pistons on my rods. I'm interested of 10.5:1.

Me · Post by Me » Sun Mar 27, 2005 7:28 am

yeah i had the same question but there is the thought of where the piston pin is located on the piston like if its lower or higher. if its higher you can try to find a longer rod which then you would be stroking for an even higher compression. there are so many things that have to be measured before this can be done so a micrometer will be your best friend

Roadrunner 16V · Post by **Roadrunner 16V** » Sun Mar 27, 2005 11:38 am

Ey norman,wat machst du denn hier? Langeweile wa?

norman · Post by **norman** » Tue Mar 29, 2005 11:41 am

moin,

na einer mu? ja hier aufpassen, sonst jagen die jungs ihre daewoos bis zum mond

und so halte ich meine k?mmerliches englisch am leben

tschau norman

Brian5475E · Post by **Brian5475E** » Wed Mar 30, 2005 1:23 am

and for the ones that only speak english here. what did you say

norman · Post by **norman** » Wed Mar 30, 2005 9:02 am

moin,

roadrunner ask me, if i have to much time, because i write here.. (we know us from other forums)

i answer, someone keep an eye on you all here, before you blow up your daewoos to the moon

and so i keep my poor english alive

just smalltalk

tschau norman

cielo20 · Post by **cielo20** » Fri Apr 01, 2005 10:25 pm

yes the opel pistons will fit perfectly with the daewoo rods as the daewoo rods are gm design!

Brian5475E · Post by **Brian5475E** » Sun Apr 03, 2005 5:55 am

I would love to get a set of those pistons here in the states