Test pipe group buy

N/A tech, Cold Air Intakes, Spark Plugs/wires, Cat backs, Exhaust...etc

Moderators: daewoomofo, Moderators Group

MMamdouh
Moderator
Posts: 7299
Joined: Wed Feb 18, 2004 8:33 am
Location: Cairo, Egypt
Contact:

Post by MMamdouh »

if for any reason you couldn't get the P/N of the CAT, compare its measurments to the following measurments:

flang to flange: 13 1/4 inch (from inside to inside)
flange thikness: 3/8 inch

i have also a 1:1 pic for the CAT gasket with 100% matches the CAT's flange and bolt pattern... the pic is 97% precise
Image

MMamdouh
Driving is the utmost fun you can have with your pants on!
Check out my ride: http://www.cardomain.com/ride/567267
Image
kinkyllama
Expert
Posts: 3772
Joined: Wed Oct 20, 2004 4:47 am
Location: USA, Arizona
Contact:

Post by kinkyllama »

mmamdouh wrote:basicly if your CAT got P/N 96350080, 96350081 or 96351364 then it will fit with no problems.

if you got other CAT then try to do some measurments concerning its lenth and flange size and bolt pattern and compare them with the pipe measurments.

MMamdouh
We are talking about the last CAT right? Mine doesnt seem to have a heat shield... but i got a # and its 96553582

for these measurments, i have to take my CAT off right?
www.KinkyMotorsports.com
04' Dropped Foreno
-Coil-overs, sway bars, 13" brakes, LSD, 235mm tires, the works
-Turbo in the works
01' Lanos Sport
-Undergoing 2.0 swap w/ lots of performance bits
http://www.cardomain.com/id/kinkyllama
MMamdouh
Moderator
Posts: 7299
Joined: Wed Feb 18, 2004 8:33 am
Location: Cairo, Egypt
Contact:

Post by MMamdouh »

well... not necessarly, you can measure the CAT length without removing it and if you can cut a paper template for the gasket i sent you can compare the flang measurments with the CAT installed as well.

it will be easyer to do so with the CAT off though.

MMamdouh
Driving is the utmost fun you can have with your pants on!
Check out my ride: http://www.cardomain.com/ride/567267
Image
kinkyllama
Expert
Posts: 3772
Joined: Wed Oct 20, 2004 4:47 am
Location: USA, Arizona
Contact:

Post by kinkyllama »

mmamdouh wrote:well... not necessarly, you can measure the CAT length without removing it and if you can cut a paper template for the gasket i sent you can compare the flang measurments with the CAT installed as well.

it will be easyer to do so with the CAT off though.

MMamdouh
PM sent... thanks again!
www.KinkyMotorsports.com
04' Dropped Foreno
-Coil-overs, sway bars, 13" brakes, LSD, 235mm tires, the works
-Turbo in the works
01' Lanos Sport
-Undergoing 2.0 swap w/ lots of performance bits
http://www.cardomain.com/id/kinkyllama
User avatar
Brian5475E
Expert
Posts: 753
Joined: Tue May 11, 2004 2:49 am
Location: Cincinnati, Ohio USA
Contact:

Post by Brian5475E »

Any news on this? also I would need a spare bottom flange. I'm redoing the cast iron pipe that bolts to the bottom of the cat. Plus I would like to get this test pipe. if I have to I could easily put the cat back in for emissions.
Aveo that moves! Now I need those cams!
Audacity Racing
moron
Posts: 4493
Joined: Wed Dec 08, 2004 5:18 am
Location: Knoxville, Tennessee
Contact:

Post by Audacity Racing »

i'm running one now to see how they work... the smell is a lot different, as for performance, i'm still evaluating it.


i can say for sure that top end has increased dramatically, but there is a flat spot on the rpm band...


i'll get back to you by the end of the week with some final details (end of next week :oops: )

sorry i haven't been keeping everyone up to date. there a lot of stuff going on and this wasn't high on my priority list especially since the post died...









i'll have news by next week as well as a pricing schedule
User avatar
Brian5475E
Expert
Posts: 753
Joined: Tue May 11, 2004 2:49 am
Location: Cincinnati, Ohio USA
Contact:

Post by Brian5475E »

can you also sell me a extra bottom flange so I can build a new down pipe under the test pipe?
Aveo that moves! Now I need those cams!
maded
Posts: 17
Joined: Sat Mar 12, 2005 2:58 am

Post by maded »

Audacityracing, are you driving a stick or an auto?
Audacity Racing
moron
Posts: 4493
Joined: Wed Dec 08, 2004 5:18 am
Location: Knoxville, Tennessee
Contact:

Post by Audacity Racing »

stick...



is it the same flange?!
maded
Posts: 17
Joined: Sat Mar 12, 2005 2:58 am

Post by maded »

Mine's a stick too but it's a 1400cc affair - F14D3-G

So i'm wondering if the flanges and everything are the same....
delphis
Expert
Posts: 724
Joined: Tue Mar 01, 2005 7:05 pm
Location: San Fransisco Bay Area
Contact:

Post by delphis »

well if it is going to be under 50 bux then you can count me in for sure
!!!!!

:)
1989 240sx fastback with SR20DE
Locked