The original daewootech forum

Hello again Yet another problem with my lanos Nearly every time i break i get a horrible grinding noise. it soounds as thought its coming from the front of the car its happend since i got the car and i have replaced the front brakes and its made no change, it now seams to be getting worse and the no...

Hallelujah WHOOOTT!!!!!!!!!! Im happy, guess what it worked lol lol lol it was faulty they repaired and got it back today and all is fine now im gonna book in its MOT and see how many times it fails lol lol lol But seriously Thanks every one in this thread and i hope some one with a similar problem ...

Thanks mezo I've done quiet a bit of digging and found this lot of info for you all.. Bosch Part numbers all start with the number 0265 and is 10 digits the number is always found on the top of the pump (where the pipes go in) and probably be covered in dirt so a good clean will result in part numbe...

Thanks Mezo You have been a great help Finding a part is proving quiet hard if even tried the scrappers and no one has this type was it only used on a few models? and the only few numbers i can find are these two 96 283 843 & TD 08208010059 But there not coming up anywhere! could the model number be...

Thanks Its been a long day been and my multimeter has had a good going over .. i've checked the wire from ster to finish and no damages :( the voltage on the red wire is about 4.74v and black is 0v all i can guess is the modulator attatced to the pump is actually faylty? or im i missing something as...

Thanks Mezo Right i disconnected the harness under the drivers seat and then tested the voltage on the red Wire there and i get noting but the resistence is only 1 Ohm same as other side but Nothing on the voltage side and from what i can see this is the fist harness in the chain from the bosch pump...

Thanks mezo Yea my abs is BOSCH so im guessing thats why i couldent find my EBCM lol as its intigrated to the pump lol.. Looking at the wiring diags i noticed that there is some mention of high resistance and the red and black wires (both repaired by me) i used the crimps and wondered if there might...

right it dident work. after a short trip to the daewoo place to reset the ecu and was told the fault still exsists :( he said it could be the wires , lol any way after a short argument i left. any way today.... followed section 4F-44 .. tested the old sensor and it works so does the current one ;) g...

Thanks you two you both answerd my question spot on, ;) so all well the light should go off after the change. But as for testing the sensors not sure how you do it but as the dealer said the wiring was fine it only leaves one area left the sensor itself.... but the question has gone through my head ...

Just talking with a mecanic im getting it all replaced with a new wheel assembly+abs and 12 months warranty, all for 110 not bad and it includes fitting! but as to the ABS warning light i was told (he's not 100%) but the Warning light re the sensor should go out after the sensor if fixed? as the abs...

Thanks for the Link VERY intresting reading from there, basicly the "confidential" Codes (Daewoo's) or any other manufactures individual codes are not on general relese they are kept "WITHIN THE COMPANY" so to speak and as such canot be put into general reades. A toyota errorcode for abs error might...

Daniel just a quick Q, using a USB adapter dongle reader and some software would you be able to read the "confidential"? just a thought there! Right the rear abs sensor went to the scrap yard and luckliy they had several Woos the only lanos they had diden't have ABS :( they had sevral Nubira's and L...

Thanks Daniel Well the chevrolet dealer said that the wires were fine and it was the sensor at fault, and ive no reason to not belive as he recomended i get it done else where due to the cost. As for the scan tool, i've been thinking of getting one but im not 100% whitch to buy as im not sure if it ...

Ive come to the conclusion that the sensore must be inside the hub.... Now i have one question before i attempt to do further damage to the car. is the rear sensor easy to get to and remove? is it a case of take of the hub assembely and its there just take of a few bolts ect or is i slightly more co...

Thans you two.. right the day of truth!! going to the scrappers later (Want to be back for the GRAND FINAL LEEDS FTW) right i've just taken off the real wheel of my car to have a look and would i be correct in thinking that the ABS SENSOR is the tiny little clip thing that goes into the wheel hub? o...